AT&T Models 1030/3070 with Feature Module 4 Uživatelský manuál stáhnout pdf (Strana 8)

Processor Module:

Works in conjunction with

Feature Module 4 to control system operating

conditions.

●

Switches A, B, C, D, E, F, G,

and

Selects

system options provided by Feature Module 4.

●

Warning light.

Red light warns of problem in

control unit. It also comes on for approximately

one minute when you first turn on the system.

Feature Module 4: Contains the software that con-

trols your

MERLIN

system. You set eight switches on

the Processor Module, according to the labels on the

Feature Module, to select the following options from

the programs stored in Feature Module

●

Attendant/Administer (10) option.

Selects at-

tendant or administration mode of operation for

the administrator/attendant console.

●

Normal/Attendant (11, 12, 13, 14) options.

Select normal or attendant mode of operation for

these four voice terminals.

●

Pooled/Square option.

Selects mode of opera-

tion for the system so that line buttons on voice

terminals represent either groups of lines

(pooled) or separate lines (square). For detailed

information on this option, see "The Square vs.

Pooled Decision," page

14.

Dial Access/Button Access option.

Sets the

●

system so that line pools can be accessed at a

voice terminal by touching a button to which the

pool is assigned or by touching a Pool Access

button and then dialing the access code for that

line pool.

●

1-8 LineS/>8 Lines option.

Sets the system size

to eight or fewer outside lines (small system) or

to more than eight lines (large system).

Diagnostics Module (optional):

Aids in identifying

faulty components if the system malfunctions.

SMDR (Station Message Detail Recording)

Module: Allows connection of a printer so you can

print out call traffic reports automatically as calls are

made. You can also issue configuration reports

whenever you want them during administration

procedures.

Services Module (optional):

Contains the following

jacks, switches, and adjusters to connect and control

optional equipment:

●

PFTT

(Power Failure Transfer Telephone) jack.

With an adapter, connects up to four standard

modular telephones for use as backup during

commercial power outage. The system

automatically switches service to them if power

fails.

●

Extra Alert jacks.

Three jacks connect strobe

lights, loud bells, or horns for three noisy or

remote zones where the regular voice terminal

ring cannot be heard.

●

Page jack.

Connects a loudspeaker paging

system. With an adapter, you can have up to

three paging zones.

Music-In jack.

Connects a music source for

Music-on-Hold or background music through a

paging system.

Bkgd Vol (Background Volume) control.

Allows

volume adjustment for background music.

MOH Vol (Music-on-Hold Volume) control.

Allows volume adjustment for Music-on-Hold.

Page Sgnl switch.

On (up) provides a short tone

before loudspeaker paging announcements. Off

(down) eliminates the signal.

Level switch.

Sets amplification for music

source. Hi (down) is for sources with their own

amplifiers; Lo (up) is for those without.

Line Module:

Provides jacks for up to five outside

lines. Normally, there are two Line Modules in the

Model 1030 control unit. You may have a third,

however, if you decide to replace the Voice Terminal

Module normally found in slot 11 with a

Line Module

in order to have 15 lines instead of 10 (1520 configura-

tion). If you add an Expansion Unit,

you will not need

this extra line capacity, and you can return your con-

trol unit to the 1030 configuration.

The Expansion Unit contains up to four Line Modules.

These modules, combined with two Line Modules in

the 1030 control unit, provide the system maximum of

six Line Modules (30 lines).

●

Jacks 0, 1, 2, 3, 4.

Connect outside lines to the

MERLIN

system. Line Modules have letters as

well as numbers. For example, the first Line

Module in the control unit is lettered A, so the

jacks in that Line Module are called A0, A1, A2,

A3, and A4.

Voice Terminal Module:

Provides jacks for ten voice

terminals. You may have up to three Voice Terminal

Modules for the Model 1030 control unit and up to four

additional Voice Terminal Modules in the Expansion

Unit. A Basic Telephone Module with jacks for basic

Touch-Tone or rotary telephones is also available.

●

“O” begins the numbering for the first five voice

terminal jacks on the module. These jacks (and

the location of the module) determine the inter-

com numbers of the voice terminals plugged in-

to them. For example, if a Voice Terminal Module

is plugged into the slot labeled “intercoms

20-29,” the jack labeled “O” is for intercom 20.

The jack below it is for intercom

21, and so on.

“5” begins the numbers for the second five voice

terminals.

Module C (optional):

An Off-Premises Telephone In-

terface to support off-premises telephones.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 122 123

Komentáře k této Příručce

Žádné komentáře

AT&T Models 1030/3070 with Feature Module 4 Uživatelský manuál Strana 8

Komentáře k této Příručce

Související produkty a manuály pro Telefony AT&T Models 1030/3070 with Feature Module 4