AT&T Definity 8410D Uživatelský manuál Strana 1

The 8400-Series Voice TerminalsInstallation and User’s Manual(includes instructions for the 8403, 8405, 8410, 8411, and 8434DX voice terminals)

3jack for connecting an analog device such as a modem, answering machines, fax machines, audio teleconferencing equipment, or TTY machines commonly us

46. Snap one end of the coiled cord into the Handset jack. This jack is labeled . (On some 8403 voice terminals, you must thread the cord into the cha

5FIGURE 2: Line, Adjunct, and Handset Cord Routing for Desktop Installation on the 8411 Voice TerminalFIGURE 3: Connecting a PC for Use with PassageWa

6FIGURE 4: Line, Adjunct, Handset, and Expansion Module Cord Routing on the 8434DX Voice Terminal7. Turn the voice terminal right side up, with the fr

7on, the voice terminal may not have power. In this case, check the connections and then verify that the particular voice terminal is administered on

8FIGURE 5: Adjusting the 8405 and 8410 Desktop StandPressinwardTabSlotsSlotsTabs Use these2 tab slotsfor the highpositionUse these2 tab slotsfor the l

9Wall InstallationNOTE: The 8403, 8405, and 8410 voice terminals can be wall-mounted. The 8411 and the 8434DX voice terminals CANNOT be wall-mounted.F

104. Place the voice terminal face down on a flat surface and turn the terminal face down.5. Remove the desktop stand which is attached to the base of

11FIGURE 8: Placing the Voice Terminal onto the Wall Jack Mounting Studs11. Snap the free end of the handset cord into the handset and place the hands

12Attaching Adjunct EquipmentIf you are installing a speakerphone (Lucent Technologies models S101A, S201A, or QUORUM® CS201A), a headset adapter (Luc

DO NOT DISCARD THE BLANK DESIGNATION CARDThe voice terminal is shipped with a blank button designation card in place under the transparent cover. Do n

13FIGURE 9: Connections for the 8434DX and All Telephones with Adjuncts Using an Individual Power Supply84xxTerminalD8ACLinecordD8WMSP-1 or the 1151A1

14USING THE RS-232-D JACK AND ANALOG ADJUNCT JACK ON THE 8411See Figure 3 in the front of this manual for a drawing of the rear of the 8411 voice term

15WARNING: Do NOT connect the Analog Adjunct to the wall jack. It will cause equipment damage.NOTE: When an 8411 voice terminal is administered at a D

16PassageWay Status IndicationsOn 8411 voice terminals, the GREEN and RED lights next to Button #9 provide the following status indications for the Pa

17LABELING THE DESIGNATION CARDThe designation card is a removable card placed behind a transparent protective cover on which the user can type or pri

18For the 8434DX Voice TerminalThere are two Call Appearance/Feature Button Designation Cards for the 8434DX voice terminal:• The smaller card contain

19• If a PC used for the PassageWay Solution software is connected to the 8411, type a “y” in the PassageWay field on the first administration screen.

20To select which channel (the I-1 Channel or the I-2 Channel) the Analog(T/R) Adjunct will use1. While on-hook, press .• The light next to goes on

21For a more detailed list of Analog Adjunct (Tip/Ring) status light indications, see “PassageWay and Analog Adjunct Status Indications on the 8411” e

22Enabling/Disabling the Status Lights for the PassageWay Connection (For the 8411 Only)If a PC for the PassageWay Solution has been connected to the

IMPORTANT USER SAFETY INSTRUCTIONSThe most careful attention has been devoted to quality standards in the manufacture of your new voice terminal. Safe

23Write: Lucent Technologies BCS Publications Center P.O. Box 4100 Crawfordsville, IN 47933Call: 1 800 457-1235 Outside U

24— DEFINITY Communications System Generic 2 and System 85 8411 Voice Terminal Quick Reference Guide, 555-104-770— DEFINITY Communications System Gene

• Never push objects of any kind into the equipment through housing slots since they may touch hazardous voltage points or short out parts that could

IMPORTANT SAFETY WARNINGS FOR INSTALLATIONWhen this product is located in a separate building from the telephone communications system, a line current

ADDITIONAL INSTALLATION WARNINGFAILURE TO FOLLOW THESE INSTRUCTIONS CAN CAUSE DAMAGE TO THE TERMINAL OR CAUSE THE ASSOCIATED PBX CIRCUIT PACK TO REMOV

INSTALLING YOUR VOICE TERMINAL . . . . . . . . . . . . . . . . . . . . . . . . . 1Distance Limitations . . . . . . . . . . . . . . . . . . . . . . .

1INSTALLING YOUR VOICE TERMINALIMPORTANT: For a fuller description of installing the 8400-Series voice terminals and procedures on administering these

2• 1145B1 Bulk Power Supply (PEC: 2404-010)Battery for the 1145B1 (2 amp battery = PEC: 24700; or 5 amp battery = PEC: 24701)• KS-22911 L2 (replaced b