AT&T 1760 Uživatelský manuál

Digital Answering Systemwith Caller ID/Call Waiting17601AT&T and the globe symbol are registered trademarks of AT&T Corp.licensed to Advanced

7Wall Installation1 Choose a location near a modular telephone jack and a standard electrical outletnot controlled by a wall switch.2 Using a pencil a

8Feature SetupYou can set up one feature at a time,or you can set up a feature and then move on to setup another feature. After you change one feature

9Answering System Feature SetupRecord Outgoing AnnouncementNOTE: If you choose not to record an announcement, the system answers with a pre-recorded a

10Ring Select and Toll SaverYou can select how many times the line will ring before the system answers a call. Set for 1 to 7 rings,or choose from two

11Announcement MonitorThis system comes set to On so you can hear your announcement when the systemanswers a call. You can reset the system so you won

12You may,however,live in a region where for calls within your Home Area Code,you mustdial 10 digits (that is,the three-digit area code and the seven

13Local Area Codes1 Press o.2 Press C or c.3 Use the softkey to select CALL ID.4 Select OKuntil the screen displays Local Area Code.5 Press C or c to

14Set Display Screen Language1 Press o.2 Press C.3 Use the softkey to select CALL ID.(or ID LLAM).4 Select OKor SI until the screen displays Language/

15Answering CallsWhen the system answers a call,the caller hears the announcement you recordedfollowed by a beep. After the beep,the system begins rec

16Listening to Your MessagesAs the system plays back messages,the screen displays the number of the message playing.Before playing each message,the sy

© 2000 Advanced American Telephones. All rights reserved.Printed in Mexico. 850002718 Issue 1AT&T 5/001760_book_1AT&T 5/1/00 7:38 PM Page

17Stop message playbackPress P.Saving messagesThe system automatically saves your messages until you delete them,and can storeapproximately 12 minutes

18Connect with the Answering System1 Dial your telephone number from a touch tone phone with a different telephonenumber.2 When the system answers,ent

19Delete MessagesDelete All Messages1 Connect with the answering system2 After you have listened to all messages and heard the two beeps,press 33. All

20Ending the Remote Access CallPress *9. The system announces,“The machine will now hang up,”and disconnectsfrom the line.Changing Remote Access Code1

21This product is designed to store and display information about incoming telephone calls.For this feature to work,the unit must be used with Caller

22NEW CALL LightThis light stays on steadily when you have received call information but have not yetreviewed it.Reviewing Call History1 To review lat

23Making a Display Dial Call1 Press C or c to locate the number in the call history that you wantto dial.2 Lift the receiver of the phone connected to

24Display MessagesPRIVATE NAME The other party is blocking name information.PRIVATE NUMBER The other party is blocking telephone number information.PR

25If this answering system does not work properly,try the following suggestions. ForCustomer Service,visit our website at www.telephones.att.com,or ca

26System Does Not Respond to Remote Commands• Make sure you are calling from a touch tone phone. When you dial a number,youshould hear tones. If you h

1760_book_1AT&T 5/1/00 7:38 PM Page iv

TEMPLATE FOR WALL MOUNTINGUse two #4 screws1760_book_1AT&T 5/1/00 7:38 PM Page 27

fold1Answering System 1760Remote CommandsTo connect with your answering system:1 Dial your telephone number from a touch tone phone.2 When the system

TWO KEY REMOTE COMMANDSTurn system off 00Delete all messages 33Review announcement 71Record announcement 7*,speak after beep,press 5 to stopRoom monit

BUTTONS AND SCREEN INDICATORS...3INSTALLATION...4About Softkeys...4Table/Des

1760_book_1AT&T 5/1/00 7:38 PM Page 2

3BUTTONS AND SCREEN INDICATORSSoftkeyNew call in callhistoryPosition of call incall historyCaller’s nameSoftkeyIndicates unreviewedcall information in

4About SoftkeysThis answering system has been designed with your convenience in mind,offering youmany features which you can access using the two “sof

52 Connect the power cord.• Plug the smaller end of the power cord into the jack labeled POWER on theback of the answering system.• Flip out the brack

66 Set the Clock.The screen displays the time (the default setting is 12 AM). To correct the setting,use C or c to correct the hour,then select NEXTto